Skip to content

stretch-minimal-rockpro64

Verschoben Linux
  • INFO'S

    ANWENDUNG

    Das Image auf eine SD-Karte schreiben, den ROCKPro64 damit starten.

    Status

    Startet nicht - Fehler!

  • Mit 0.7.2 startet das Image. LAN ok.

    rock64@rockpro64:~$ iperf3 -c 192.168.3.213
    Connecting to host 192.168.3.213, port 5201
    [  4] local 192.168.3.9 port 33558 connected to 192.168.3.213 port 5201
    [ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
    [  4]   0.00-1.00   sec   116 MBytes   970 Mbits/sec    0    938 KBytes       
    [  4]   1.00-2.00   sec   112 MBytes   942 Mbits/sec    0   1012 KBytes       
    [  4]   2.00-3.00   sec   112 MBytes   942 Mbits/sec    0   1.00 MBytes       
    [  4]   3.00-4.00   sec   112 MBytes   941 Mbits/sec    0   1.11 MBytes       
    [  4]   4.00-5.00   sec   112 MBytes   941 Mbits/sec    0   1.11 MBytes       
    [  4]   5.00-6.00   sec   112 MBytes   941 Mbits/sec    0   1.11 MBytes       
    [  4]   6.00-7.00   sec   106 MBytes   890 Mbits/sec    0   6.01 MBytes       
    [  4]   7.00-8.00   sec   113 MBytes   952 Mbits/sec    0   6.01 MBytes       
    [  4]   8.00-9.00   sec   112 MBytes   941 Mbits/sec    0   6.01 MBytes       
    [  4]   9.00-10.00  sec   112 MBytes   942 Mbits/sec    0   6.01 MBytes       
    - - - - - - - - - - - - - - - - - - - - - - - - -
    [ ID] Interval           Transfer     Bandwidth       Retr
    [  4]   0.00-10.00  sec  1.09 GBytes   940 Mbits/sec    0             sender
    [  4]   0.00-10.00  sec  1.09 GBytes   937 Mbits/sec                  receiver
    
    iperf Done.
    rock64@rockpro64:~$ iperf3 -s              
    -----------------------------------------------------------
    Server listening on 5201
    -----------------------------------------------------------
    Accepted connection from 192.168.3.213, port 51756
    [  5] local 192.168.3.9 port 5201 connected to 192.168.3.213 port 51758
    [ ID] Interval           Transfer     Bandwidth
    [  5]   0.00-1.00   sec   110 MBytes   923 Mbits/sec                  
    [  5]   1.00-2.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   2.00-3.00   sec   112 MBytes   942 Mbits/sec                  
    [  5]   3.00-4.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   4.00-5.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   5.00-6.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   6.00-7.00   sec   112 MBytes   942 Mbits/sec                  
    [  5]   7.00-8.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   8.00-9.00   sec   112 MBytes   941 Mbits/sec                  
    [  5]   9.00-10.00  sec   112 MBytes   942 Mbits/sec                  
    [  5]  10.00-10.02  sec  1.79 MBytes   931 Mbits/sec                  
    - - - - - - - - - - - - - - - - - - - - - - - - -
    [ ID] Interval           Transfer     Bandwidth
    [  5]   0.00-10.02  sec  0.00 Bytes  0.00 bits/sec                  sender
    [  5]   0.00-10.02  sec  1.10 GBytes   940 Mbits/sec                  receiver
    -----------------------------------------------------------
    Server listening on 5201
    -----------------------------------------------------------
    ^Ciperf3: interrupt - the server has terminated
    
  • Mal ein Test was der Speicher so kann.

    rock64@rockpro64:~/tinymembench$ ./tinymembench
    tinymembench v0.4.9 (simple benchmark for memory throughput and latency)
    
    ==========================================================================
    == Memory bandwidth tests                                               ==
    ==                                                                      ==
    == Note 1: 1MB = 1000000 bytes                                          ==
    == Note 2: Results for 'copy' tests show how many bytes can be          ==
    ==         copied per second (adding together read and writen           ==
    ==         bytes would have provided twice higher numbers)              ==
    == Note 3: 2-pass copy means that we are using a small temporary buffer ==
    ==         to first fetch data into it, and only then write it to the   ==
    ==         destination (source -> L1 cache, L1 cache -> destination)    ==
    == Note 4: If sample standard deviation exceeds 0.1%, it is shown in    ==
    ==         brackets                                                     ==
    ==========================================================================
    
     C copy backwards                                     :   2812.7 MB/s
     C copy backwards (32 byte blocks)                    :   2811.9 MB/s
     C copy backwards (64 byte blocks)                    :   2632.8 MB/s
     C copy                                               :   2667.2 MB/s
     C copy prefetched (32 bytes step)                    :   2633.5 MB/s
     C copy prefetched (64 bytes step)                    :   2640.8 MB/s
     C 2-pass copy                                        :   2509.8 MB/s
     C 2-pass copy prefetched (32 bytes step)             :   2431.6 MB/s
     C 2-pass copy prefetched (64 bytes step)             :   2424.1 MB/s
     C fill                                               :   4887.7 MB/s (0.5%)
     C fill (shuffle within 16 byte blocks)               :   4883.0 MB/s
     C fill (shuffle within 32 byte blocks)               :   4889.3 MB/s
     C fill (shuffle within 64 byte blocks)               :   4889.2 MB/s
     ---
     standard memcpy                                      :   2807.3 MB/s
     standard memset                                      :   4890.4 MB/s (0.3%)
     ---
     NEON LDP/STP copy                                    :   2803.7 MB/s
     NEON LDP/STP copy pldl2strm (32 bytes step)          :   2802.1 MB/s
     NEON LDP/STP copy pldl2strm (64 bytes step)          :   2800.7 MB/s
     NEON LDP/STP copy pldl1keep (32 bytes step)          :   2745.5 MB/s
     NEON LDP/STP copy pldl1keep (64 bytes step)          :   2745.8 MB/s
     NEON LD1/ST1 copy                                    :   2801.9 MB/s
     NEON STP fill                                        :   4888.9 MB/s (0.3%)
     NEON STNP fill                                       :   4850.1 MB/s
     ARM LDP/STP copy                                     :   2803.8 MB/s
     ARM STP fill                                         :   4893.0 MB/s (0.5%)
     ARM STNP fill                                        :   4851.7 MB/s
    
    ==========================================================================
    == Framebuffer read tests.                                              ==
    ==                                                                      ==
    == Many ARM devices use a part of the system memory as the framebuffer, ==
    == typically mapped as uncached but with write-combining enabled.       ==
    == Writes to such framebuffers are quite fast, but reads are much       ==
    == slower and very sensitive to the alignment and the selection of      ==
    == CPU instructions which are used for accessing memory.                ==
    ==                                                                      ==
    == Many x86 systems allocate the framebuffer in the GPU memory,         ==
    == accessible for the CPU via a relatively slow PCI-E bus. Moreover,    ==
    == PCI-E is asymmetric and handles reads a lot worse than writes.       ==
    ==                                                                      ==
    == If uncached framebuffer reads are reasonably fast (at least 100 MB/s ==
    == or preferably >300 MB/s), then using the shadow framebuffer layer    ==
    == is not necessary in Xorg DDX drivers, resulting in a nice overall    ==
    == performance improvement. For example, the xf86-video-fbturbo DDX     ==
    == uses this trick.                                                     ==
    ==========================================================================
    
     NEON LDP/STP copy (from framebuffer)                 :    602.5 MB/s
     NEON LDP/STP 2-pass copy (from framebuffer)          :    551.6 MB/s
     NEON LD1/ST1 copy (from framebuffer)                 :    667.1 MB/s
     NEON LD1/ST1 2-pass copy (from framebuffer)          :    605.6 MB/s
     ARM LDP/STP copy (from framebuffer)                  :    445.3 MB/s
     ARM LDP/STP 2-pass copy (from framebuffer)           :    428.8 MB/s
    
    ==========================================================================
    == Memory latency test                                                  ==
    ==                                                                      ==
    == Average time is measured for random memory accesses in the buffers   ==
    == of different sizes. The larger is the buffer, the more significant   ==
    == are relative contributions of TLB, L1/L2 cache misses and SDRAM      ==
    == accesses. For extremely large buffer sizes we are expecting to see   ==
    == page table walk with several requests to SDRAM for almost every      ==
    == memory access (though 64MiB is not nearly large enough to experience ==
    == this effect to its fullest).                                         ==
    ==                                                                      ==
    == Note 1: All the numbers are representing extra time, which needs to  ==
    ==         be added to L1 cache latency. The cycle timings for L1 cache ==
    ==         latency can be usually found in the processor documentation. ==
    == Note 2: Dual random read means that we are simultaneously performing ==
    ==         two independent memory accesses at a time. In the case if    ==
    ==         the memory subsystem can't handle multiple outstanding       ==
    ==         requests, dual random read has the same timings as two       ==
    ==         single reads performed one after another.                    ==
    ==========================================================================
    
    block size : single random read / dual random read
          1024 :    0.0 ns          /     0.0 ns 
          2048 :    0.0 ns          /     0.0 ns 
          4096 :    0.0 ns          /     0.0 ns 
          8192 :    0.0 ns          /     0.0 ns 
         16384 :    0.0 ns          /     0.0 ns 
         32768 :    0.0 ns          /     0.0 ns 
         65536 :    4.5 ns          /     7.2 ns 
        131072 :    6.8 ns          /     9.7 ns 
        262144 :    9.8 ns          /    12.8 ns 
        524288 :   11.4 ns          /    14.7 ns 
       1048576 :   16.0 ns          /    22.6 ns 
       2097152 :  114.0 ns          /   175.3 ns 
       4194304 :  161.7 ns          /   219.9 ns 
       8388608 :  190.7 ns          /   241.5 ns 
      16777216 :  205.3 ns          /   250.5 ns 
      33554432 :  212.9 ns          /   255.5 ns 
      67108864 :  222.3 ns          /   271.1 ns
    

  • 1 Stimmen
    13 Beiträge
    1k Aufrufe
    FrankMF

    Ich möchte das dann hier zum Abschluss bringen, das NAS ist heute zusammengebaut worden. Hier zwei Fotos.

    IMG_20200425_102156_ergebnis.jpg

    IMG_20200425_102206_ergebnis.jpg

  • linux-mainline-u-boot

    Angeheftet Images
    2
    0 Stimmen
    2 Beiträge
    349 Aufrufe
    FrankMF

    2020.01-ayufan-2014-gff2cdd38 released

    ayufan: rockchip: allow to boot scsi4, as JMS585 can have 5 drives
  • Images 0.10.x

    Angeheftet Images
    10
    0 Stimmen
    10 Beiträge
    415 Aufrufe
    FrankMF

    0.10.12: gitlab-ci-linux-build-184 released

    0.10.12: Be strict on any qemu failures 0.10.12: Build by default mate/lxde/gnome/xfce4 0.10.12: Add pcie scan delay from @nuumio 0.10.12: Add ubuntu-mate-lightdm-theme where possible

    Ich komme gar nicht mehr mit dem Testen hinterher 🙂

  • Image 0.9.14 - Kurztest

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    216 Aufrufe
    Niemand hat geantwortet
  • Debian Minimal von Mr.Fixit2001

    Linux
    4
    0 Stimmen
    4 Beiträge
    429 Aufrufe
    FrankMF

    Release 190531 - Updated Debian Minimal Release

    Kernel Updated to 4.4.180 Additional Kernel Fixes U-Boot patched to fix weird issue where only some EMMC modules will not boot
  • 0 Stimmen
    2 Beiträge
    485 Aufrufe
    FrankMF

    Das ist das Ergebnis des Stresstests 😞

    [ 2461.489468] ata2.00: exception Emask 0x10 SAct 0xffffffff SErr 0x400000 action 0x6 frozen [ 2461.490206] ata2.00: irq_stat 0x08000000, interface fatal error [ 2461.490732] ata2: SError: { Handshk } [ 2461.491062] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.491532] ata2.00: cmd 61/40:00:f8:a6:64/05:00:84:00:00/40 tag 0 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.492993] ata2.00: status: { DRDY } [ 2461.493327] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.493796] ata2.00: cmd 61/c0:08:38:ac:64/03:00:84:00:00/40 tag 1 ncq dma 491520 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.495181] ata2.00: status: { DRDY } [ 2461.495507] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.496276] ata2.00: cmd 61/c0:10:a0:f5:64/02:00:84:00:00/40 tag 2 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.497697] ata2.00: status: { DRDY } [ 2461.498029] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.498497] ata2.00: cmd 61/40:18:60:f8:64/05:00:84:00:00/40 tag 3 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.499886] ata2.00: status: { DRDY } [ 2461.500213] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.500681] ata2.00: cmd 61/c0:20:a0:fd:64/02:00:84:00:00/40 tag 4 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.502087] ata2.00: status: { DRDY } [ 2461.502416] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.502884] ata2.00: cmd 61/40:28:60:00:65/05:00:84:00:00/40 tag 5 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.505026] ata2.00: status: { DRDY } [ 2461.505378] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.505852] ata2.00: cmd 61/c0:30:a0:05:65/02:00:84:00:00/40 tag 6 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.507244] ata2.00: status: { DRDY } [ 2461.507572] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.508040] ata2.00: cmd 61/40:38:60:08:65/05:00:84:00:00/40 tag 7 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.509472] ata2.00: status: { DRDY } [ 2461.509808] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.510277] ata2.00: cmd 61/a0:40:a0:0d:65/02:00:84:00:00/40 tag 8 ncq dma 344064 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.511667] ata2.00: status: { DRDY } [ 2461.511994] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.512461] ata2.00: cmd 61/40:48:00:20:66/05:00:84:00:00/40 tag 9 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.514503] ata2.00: status: { DRDY } [ 2461.514850] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.515322] ata2.00: cmd 61/40:50:00:28:66/05:00:84:00:00/40 tag 10 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.516721] ata2.00: status: { DRDY } [ 2461.517084] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.517562] ata2.00: cmd 61/c0:58:40:2d:66/02:00:84:00:00/40 tag 11 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.519253] ata2.00: status: { DRDY } [ 2461.519595] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.520066] ata2.00: cmd 61/40:60:f8:9e:64/05:00:84:00:00/40 tag 12 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.521504] ata2.00: status: { DRDY } [ 2461.521840] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.522309] ata2.00: cmd 61/c0:68:38:a4:64/02:00:84:00:00/40 tag 13 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.523706] ata2.00: status: { DRDY } [ 2461.524033] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.524501] ata2.00: cmd 61/40:70:f8:af:64/05:00:84:00:00/40 tag 14 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.525925] ata2.00: status: { DRDY } [ 2461.526256] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.526725] ata2.00: cmd 61/c0:78:38:b5:64/02:00:84:00:00/40 tag 15 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.528122] ata2.00: status: { DRDY } [ 2461.528449] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.528939] ata2.00: cmd 61/40:80:f8:b7:64/05:00:84:00:00/40 tag 16 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.530339] ata2.00: status: { DRDY } [ 2461.530667] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.531136] ata2.00: cmd 61/c0:88:38:bd:64/02:00:84:00:00/40 tag 17 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.532532] ata2.00: status: { DRDY } [ 2461.532880] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.533357] ata2.00: cmd 61/40:90:f8:bf:64/05:00:84:00:00/40 tag 18 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.534754] ata2.00: status: { DRDY } [ 2461.535081] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.535549] ata2.00: cmd 61/c0:98:38:c5:64/02:00:84:00:00/40 tag 19 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.536970] ata2.00: status: { DRDY } [ 2461.537301] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.537769] ata2.00: cmd 61/40:a0:f8:c7:64/05:00:84:00:00/40 tag 20 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.539165] ata2.00: status: { DRDY } [ 2461.539491] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.539960] ata2.00: cmd 61/c0:a8:38:cd:64/02:00:84:00:00/40 tag 21 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.541381] ata2.00: status: { DRDY } [ 2461.541713] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.542182] ata2.00: cmd 61/40:b0:f8:cf:64/05:00:84:00:00/40 tag 22 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.543577] ata2.00: status: { DRDY } [ 2461.543905] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.544374] ata2.00: cmd 61/40:b8:f8:d7:64/05:00:84:00:00/40 tag 23 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.545790] ata2.00: status: { DRDY } [ 2461.546120] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.546589] ata2.00: cmd 61/c0:c0:38:dd:64/02:00:84:00:00/40 tag 24 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.547987] ata2.00: status: { DRDY } [ 2461.548314] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.548782] ata2.00: cmd 61/a8:c8:f8:df:64/05:00:84:00:00/40 tag 25 ncq dma 741376 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.550198] ata2.00: status: { DRDY } [ 2461.550530] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.550999] ata2.00: cmd 61/c0:d0:a0:e5:64/02:00:84:00:00/40 tag 26 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.552396] ata2.00: status: { DRDY } [ 2461.552723] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.553208] ata2.00: cmd 61/40:d8:60:e8:64/05:00:84:00:00/40 tag 27 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.554607] ata2.00: status: { DRDY } [ 2461.554935] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.555404] ata2.00: cmd 61/c0:e0:a0:ed:64/02:00:84:00:00/40 tag 28 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.556800] ata2.00: status: { DRDY } [ 2461.557145] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.557617] ata2.00: cmd 61/40:e8:60:f0:64/05:00:84:00:00/40 tag 29 ncq dma 688128 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.559012] ata2.00: status: { DRDY } [ 2461.559340] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.559807] ata2.00: cmd 61/c0:f0:38:d5:64/02:00:84:00:00/40 tag 30 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.561221] ata2.00: status: { DRDY } [ 2461.561552] ata2.00: failed command: WRITE FPDMA QUEUED [ 2461.562021] ata2.00: cmd 61/c0:f8:40:25:66/02:00:84:00:00/40 tag 31 ncq dma 360448 out res 40/00:50:00:28:66/00:00:84:00:00/40 Emask 0x10 (ATA bus error) [ 2461.563416] ata2.00: status: { DRDY } [ 2461.563752] ata2: hard resetting link [ 2471.561504] ata2: softreset failed (1st FIS failed) [ 2471.561959] ata2: hard resetting link [ 2481.560785] ata2: softreset failed (1st FIS failed) [ 2481.561238] ata2: hard resetting link [ 2516.561654] ata2: softreset failed (1st FIS failed) [ 2516.562109] ata2: limiting SATA link speed to 3.0 Gbps [ 2516.562113] ata2: hard resetting link [ 2521.561261] ata2: softreset failed (1st FIS failed) [ 2521.561715] ata2: reset failed, giving up [ 2521.562074] ata2.00: disabled [ 2521.562575] ata2: EH complete [ 2521.562677] sd 1:0:0:0: [sdb] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562686] sd 1:0:0:0: [sdb] tag#18 CDB: opcode=0x35 35 00 00 00 00 00 00 00 00 00 [ 2521.562701] print_req_error: I/O error, dev sdb, sector 0 [ 2521.562791] sd 1:0:0:0: [sdb] tag#20 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562802] sd 1:0:0:0: [sdb] tag#19 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.562873] sd 1:0:0:0: [sdb] tag#19 CDB: opcode=0x2a 2a 00 84 66 25 40 00 02 c0 00 [ 2521.562888] print_req_error: I/O error, dev sdb, sector 2221286720 [ 2521.563107] sd 1:0:0:0: [sdb] tag#21 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.563126] sd 1:0:0:0: [sdb] tag#21 CDB: opcode=0x2a 2a 00 84 64 f0 60 00 05 40 00 [ 2521.563138] print_req_error: I/O error, dev sdb, sector 2221207648 [ 2521.563422] sd 1:0:0:0: [sdb] tag#22 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.563772] sd 1:0:0:0: [sdb] tag#20 CDB: opcode=0x2a 2a 00 84 64 d5 38 00 02 c0 00 [ 2521.564326] print_req_error: I/O error, dev sdb, sector 2221200696 [ 2521.564337] sd 1:0:0:0: [sdb] tag#22 CDB: opcode=0x2a 2a 00 84 64 ed a0 00 02 c0 00 [ 2521.564896] print_req_error: I/O error, dev sdb, sector 2221206944 [ 2521.565088] sd 1:0:0:0: [sdb] tag#26 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.565469] sd 1:0:0:0: [sdb] tag#26 CDB: opcode=0x2a 2a 00 84 64 dd 38 00 02 c0 00 [ 2521.565483] print_req_error: I/O error, dev sdb, sector 2221202744 [ 2521.565610] sd 1:0:0:0: [sdb] tag#23 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.566056] sd 1:0:0:0: [sdb] tag#23 CDB: opcode=0x2a 2a 00 84 64 e8 60 00 05 40 00 [ 2521.566069] print_req_error: I/O error, dev sdb, sector 2221205600 [ 2521.566183] sd 1:0:0:0: [sdb] tag#29 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.566641] sd 1:0:0:0: [sdb] tag#29 CDB: opcode=0x2a 2a 00 84 64 cd 38 00 02 c0 00 [ 2521.566654] print_req_error: I/O error, dev sdb, sector 2221198648 [ 2521.566954] sd 1:0:0:0: [sdb] tag#24 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.567224] sd 1:0:0:0: [sdb] tag#24 CDB: opcode=0x2a 2a 00 84 64 e5 a0 00 02 c0 00 [ 2521.567237] print_req_error: I/O error, dev sdb, sector 2221204896 [ 2521.567459] sd 1:0:0:0: [sdb] tag#30 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2521.567809] sd 1:0:0:0: [sdb] tag#30 CDB: opcode=0x2a 2a 00 84 64 c7 f8 00 05 40 00 [ 2521.567821] print_req_error: I/O error, dev sdb, sector 2221197304 [ 2521.584903] md: super_written gets error=10 [ 2521.585306] md/raid1:md0: Disk failure on dm-1, disabling device. md/raid1:md0: Operation continuing on 1 devices. [ 2526.581450] scsi_io_completion_action: 41779 callbacks suppressed [ 2526.581461] sd 1:0:0:0: [sdb] tag#27 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.581467] sd 1:0:0:0: [sdb] tag#27 CDB: opcode=0x2a 2a 00 84 66 7d 50 00 00 01 00 [ 2526.581469] print_req_error: 41780 callbacks suppressed [ 2526.581471] print_req_error: I/O error, dev sdb, sector 2221309264 [ 2526.582524] sd 1:0:0:0: [sdb] tag#28 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.582530] sd 1:0:0:0: [sdb] tag#28 CDB: opcode=0x2a 2a 00 84 66 7d 51 00 00 01 00 [ 2526.582534] print_req_error: I/O error, dev sdb, sector 2221309265 [ 2526.583366] sd 1:0:0:0: [sdb] tag#29 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.583370] sd 1:0:0:0: [sdb] tag#29 CDB: opcode=0x2a 2a 00 84 66 7d 52 00 00 01 00 [ 2526.583373] print_req_error: I/O error, dev sdb, sector 2221309266 [ 2526.584113] sd 1:0:0:0: [sdb] tag#30 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.584117] sd 1:0:0:0: [sdb] tag#30 CDB: opcode=0x2a 2a 00 84 66 7d 53 00 00 01 00 [ 2526.584119] print_req_error: I/O error, dev sdb, sector 2221309267 [ 2526.584960] sd 1:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.584968] sd 1:0:0:0: [sdb] tag#0 CDB: opcode=0x2a 2a 00 84 66 7d 54 00 00 01 00 [ 2526.584971] print_req_error: I/O error, dev sdb, sector 2221309268 [ 2526.585765] sd 1:0:0:0: [sdb] tag#1 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.585769] sd 1:0:0:0: [sdb] tag#1 CDB: opcode=0x2a 2a 00 84 66 7d 55 00 00 01 00 [ 2526.585772] print_req_error: I/O error, dev sdb, sector 2221309269 [ 2526.586461] sd 1:0:0:0: [sdb] tag#2 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.586465] sd 1:0:0:0: [sdb] tag#2 CDB: opcode=0x2a 2a 00 84 66 7d 56 00 00 01 00 [ 2526.586468] print_req_error: I/O error, dev sdb, sector 2221309270 [ 2526.587144] sd 1:0:0:0: [sdb] tag#3 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.587148] sd 1:0:0:0: [sdb] tag#3 CDB: opcode=0x2a 2a 00 84 66 7d 57 00 00 01 00 [ 2526.587150] print_req_error: I/O error, dev sdb, sector 2221309271 [ 2526.587734] sd 1:0:0:0: [sdb] tag#4 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.587737] sd 1:0:0:0: [sdb] tag#4 CDB: opcode=0x2a 2a 00 84 66 7d 58 00 00 01 00 [ 2526.587739] print_req_error: I/O error, dev sdb, sector 2221309272 [ 2526.588320] sd 1:0:0:0: [sdb] tag#5 UNKNOWN(0x2003) Result: hostbyte=0x04 driverbyte=0x00 [ 2526.588323] sd 1:0:0:0: [sdb] tag#5 CDB: opcode=0x2a 2a 00 84 66 7d 59 00 00 01 00 [ 2526.588325] print_req_error: I/O error, dev sdb, sector 2221309273

    Und, wieder eine Platte im Raid1 verloren

    rock64@rockpro64v_2_1:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 dm-1[2](F) dm-0[1] 1953379392 blocks super 1.2 [2/1] [_U] bitmap: 5/15 pages [20KB], 65536KB chunk unused devices: <none>

    Leider habe ich nicht die Kenntnisse um zu erkennen, woran das liegt.

  • 0 Stimmen
    1 Beiträge
    471 Aufrufe
    Niemand hat geantwortet
  • [HOWTO]ROCKPro64 - NAS bauen Teil 1

    Angeheftet ROCKPro64
    5
    0 Stimmen
    5 Beiträge
    2k Aufrufe
    FrankMF

    Die Pinne für den Adapter liegen ja nur parallel zum Eingang des Steckers vom Netzteil. Also, solange da nichts abfackelt kann man da eine Menge Strom drüber jagen 🙂

    Wenn es funktioniert ist ja alles gut.