Skip to content

FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6

Linux
  • Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

  • @mabs sagte in FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6:

    Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

    Thanks, i will try the fan tool again. I'm almost sure i did try without luck, have you edited something in the fan tool conf..?

  • Hi,

    I only played with two parameters.

    I have two rockpro64 boards, currently one has a small fan and the other one has a large fan.

    Therefore I changed PROFILE_NR accordingly.

    Also I have ALWAYS_ON on true on the one with the large fan, but don't see a difference. The fan goes on and off still, maybe I misinterpreted the parameter.

    Also I just noticed now that the CTL settings of the version on github changed slightly, but I think this only improved the detection depending of the kernel settings.

    M

  • @mabs

    With the new OMV kernel 5.6 image from Auyfan, i can't get the FAN to spin - If the fan spins it runs really slow, no sound from the fan.

    With the FAN tool the master installation "failed" and with the release installation it did report "active"..
    I have installed a 92mm FAN inside the NAS case, it runs on Armbian with kernel 5.4.32

    I will open op the case later today to be sure. Thanks.

  • Hi,

    Now i did find the fan, here it goes "nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1" it is at "0" can be controlled to "255"

    Best Regards.

  • Yes that is basically the way ATS is doing the changing as well I think, as those /sys entries are in the _CTL variables.

    good that you got it working, or are you only half way?

    M

  • @mabs

    The tool works on all image under 5.4 or so for me. But yes i am at the finish line, just wanted the fan to be always on. Just wanted to share, if someone will run in the same problems. Thanks.

  • Helpful Thread!

    But, ATS don't work for me on kernel 5.6 with ayufan release. Only this command works.

    nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    Thanks @soerenderfor for the hint.

  • Ok, problem in ATS is this?

    -- FAN Control[ String ]
    	PWM_CTL		= {
    			"/sys/class/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1"
    	},
    
  • @FrankM - did you try fix the ATS tool, if yes. Will it Work?

    Best Regards.

  • Hi,

    since I'm currently change my rockpro64 setup I came across this.

    With the kernel from ayufan you need to set PWM_CTL to

    /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    for my self compiled one I need

    /sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1
    

    But I got it only working with one entry for PWM_CTL e.g.

    PWM_CTL		= "/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    

    after that you need to start ats again

    sudo systemctl stop ats
    sudo systemctl start ats
    

    initially the fan should start immediately for a short period of time.

    In case it is even a different one on your kernel you can find the right one using this command.

    sudo find /sys -name pwm1 | grep hwmon
    

    So far I'm not sure which kernel parameter or modul changes this.

    Martin

  • Update 1.30.3 released

    Vaultwarden
    1
    0 Stimmen
    1 Beiträge
    67 Aufrufe
    Niemand hat geantwortet
  • Debian 11.1 released

    Linux
    1
    0 Stimmen
    1 Beiträge
    140 Aufrufe
    Niemand hat geantwortet
  • Images 0.11.x

    Images
    5
    0 Stimmen
    5 Beiträge
    323 Aufrufe
    FrankMF

    0.11.2: gitlab-ci-linux-build-187 released

    0.11.2: Update OMV install (to also be able to run OMV6)
  • 0 Stimmen
    3 Beiträge
    315 Aufrufe
    FrankMF

    @thrakath1980 Das kann ich Dir leider nicht beantworten. Denke aber, das es sinnvoll ist neu anzufangen. Welche Settings meinst Du?

    Ich würde mal /etc/config sichern. Da sollte das Meiste ja drin sein.

    Notifications? Hmm, ich hoffe das das funktioniert. Ich schau zur Sicherheit mal nach.

  • checkmk - Dockerinstallation

    Verschoben checkmk
    9
    0 Stimmen
    9 Beiträge
    949 Aufrufe
    FrankMF

    Und noch was Wichtiges.

    6777da6e-3b4f-41b9-bf6e-26496ae67cd8-grafik.png

    Damit sichert man den Datenaustausch ab.

    Kapitel 7.4. Inbuilt encryption

    Den Ordner findet man hier -> /etc/check_mk/encryption.cfg

  • Mainline Kernel 4.18.0-rc3

    Linux
    1
    0 Stimmen
    1 Beiträge
    945 Aufrufe
    Niemand hat geantwortet
  • Mainline Kernel 4.20.x

    Verschoben Images
    26
    0 Stimmen
    26 Beiträge
    4k Aufrufe
    FrankMF

    4.20.0-1090-ayufan released

    Änderungen -> https://gitlab.com/ayufan-repos/rock64/linux-mainline-kernel/commits/master

  • Mainline Kernel 4.17-rc7

    Verschoben Archiv
    8
    0 Stimmen
    8 Beiträge
    2k Aufrufe
    FrankMF

    4.17.0-rc6-1029-ayufan released

    Link Preview Image Releases · ayufan-rock64/linux-mainline-kernel

    Linux kernel source tree. Contribute to ayufan-rock64/linux-mainline-kernel development by creating an account on GitHub.

    favicon

    GitHub (github.com)

    Seit 1021 funktioniert USB3.