Skip to content

0.6.59 released

Verschoben Archiv
  • 0.6.59 released

    0.6.59: Fix u-boot dtb: fixes reboot, cpu stability issues, usb2/type-c booting,
    0.6.59: Enable leds support in u-boot,
    0.6.59: Fix rock64_upgrade_bootloader.sh script,
    0.6.59: Fix extlinux kernel sorting,
    0.6.59: Copy-paste evb_rk3399 to rockpro64_rk3399 in u-boot,
    0.6.59: Use proper fcs,suspend-voltage-selector for vdd_cpu_b on mainline kernel,
    0.6.59: Rebase mainline kernel on 4.18.0-rc3 (requires 0.6.59 u-boot),
    0.6.59: Rebase 4.4 kernel on rockchip-linux/kernel@40e8774,
    

    Kamil war gestern Abend noch fleißig 🙂

    Beim Booten von 0.6.59 kommen zwar immer noch die Memory Fehler, aber irgendwann startet es mal. Die NVMe-Karte wurde nicht eingebunden. Aber hiermit war das kein Problem.

    Danach gibt die NVMe-Karte folgendes aus

    root@rockpro64:/home/rock64# lspci -vvv
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 236
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
    	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
    		Address: 00000000fee30040  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    	Kernel driver in use: pcieport
    
    01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 (prog-if 02 [NVM Express])
    	Subsystem: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 235
    	Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=16K]
    	Capabilities: [40] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+
    		Address: 0000000000000000  Data: 0000
    	Capabilities: [70] Express (v2) Endpoint, MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    		LnkCap:	Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L0s unlimited, L1 <64us
    			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
    		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [b0] MSI-X: Enable+ Count=8 Masked-
    		Vector table: BAR=0 offset=00003000
    		PBA: BAR=0 offset=00002000
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [148 v1] Device Serial Number 00-00-00-00-00-00-00-00
    	Capabilities: [158 v1] Power Budgeting <?>
    	Capabilities: [168 v1] #19
    	Capabilities: [188 v1] Latency Tolerance Reporting
    		Max snoop latency: 0ns
    		Max no snoop latency: 0ns
    	Capabilities: [190 v1] L1 PM Substates
    		L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
    			  PortCommonModeRestoreTime=10us PortTPowerOnTime=10us
    		L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
    			   T_CommonMode=0us LTR1.2_Threshold=0ns
    		L1SubCtl2: T_PwrOn=10us
    	Kernel driver in use: nvme
    

    Da ist ja endlich das x4 !!!

    LnkSta:	Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    

    Speedtest

    root@rockpro64:/mnt# sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync
    4096+0 records in
    4096+0 records out
    4294967296 bytes (4.3 GB, 4.0 GiB) copied, 11.3636 s, 378 MB/s
    

    und

    root@rockpro64:/mnt# sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 
     	Iozone: Performance Test of File I/O
     	        Version $Revision: 3.429 $
     		Compiled for 64 bit mode.
     		Build: linux 
     
     	Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
     	             Al Slater, Scott Rhine, Mike Wisner, Ken Goss
     	             Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR,
     	             Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner,
     	             Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone,
     	             Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root,
     	             Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer,
     	             Vangel Bojaxhi, Ben England, Vikentsi Lapa.
     
     	Run began: Wed Jul  4 03:21:54 2018
     
     	Include fsync in write timing
     	O_DIRECT feature enabled
     	Auto Mode
     	File size set to 102400 kB
     	Record Size 4 kB
     	Record Size 16 kB
     	Record Size 512 kB
     	Record Size 1024 kB
     	Record Size 16384 kB
     	Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2
     	Output is in kBytes/sec
     	Time Resolution = 0.000001 seconds.
     	Processor cache size set to 1024 kBytes.
     	Processor cache line size set to 32 bytes.
     	File stride size set to 17 * record size.
                                                                   random    random     bkwd    record    stride                                    
                   kB  reclen    write  rewrite    read    reread    read     write     read   rewrite      read   fwrite frewrite    fread  freread
               102400       4    69551   109290   128601   114462    25822    73054                                                          
               102400      16   133640   240685   269449   273207   117705   192497                                                          
               102400     512   582963   588868   458828   465076   417720   551456                                                          
               102400    1024   519443   628637   490247   497807   468750   627362                                                          
               102400   16384   977517  1048544  1032961  1097595  1070311  1094686   
    

    Das sieht und "fühlt" sich schon viel besser an 🙂

    Das hier

    0.6.59: Rebase mainline kernel on 4.18.0-rc3 (requires 0.6.59 u-boot),
    

    bedeutet, das ich meine Mainline Installation mit einer 0.6.59 Installation erneut machen muss, damit der neue u-boot benutzt wird. Doch erst mal Geld verdienen... 😉

  • TwisterOS

    Images
    1
    0 Stimmen
    1 Beiträge
    225 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - PCIe Probleme

    Hardware
    3
    0 Stimmen
    3 Beiträge
    303 Aufrufe
    FrankMF

    Danke für dein Feedback.

  • ROCKPro64 - i2c Bus

    Hardware
    1
    0 Stimmen
    1 Beiträge
    512 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - Armbian nand-sata-install

    Verschoben Armbian
    14
    0 Stimmen
    14 Beiträge
    2k Aufrufe
    FrankMF

    Ich habe heute, nachdem es einige Updates von Armbian gab, mal nachgeschaut ob ein spezieller Fehler verschwunden ist.
    Und zwar geht es um das Resizen der Partion nachdem wir Armbian auf eine USB-HDD (USB3) installiert haben.

    Ich setze dafür folgendes System ein.

    Hardware ROCKPro64v2.0 4GB RAM SanDisk 240GB 2,5 Zoll HDD (nix tolles) Software Welcome to ARMBIAN 5.67.181217 nightly Debian GNU/Linux 9 (stretch) 4.4.167-rockchip64

    Was sehe ich nach dem Reboot?

    root@rockpro64:~# df -h Filesystem Size Used Avail Use% Mounted on udev 1.9G 0 1.9G 0% /dev tmpfs 388M 5.3M 383M 2% /run /dev/sda1 220G 1.3G 207G 1% / tmpfs 1.9G 0 1.9G 0% /dev/shm tmpfs 5.0M 4.0K 5.0M 1% /run/lock tmpfs 1.9G 0 1.9G 0% /sys/fs/cgroup tmpfs 1.9G 4.0K 1.9G 1% /tmp /dev/mmcblk0p1 58G 1.3G 57G 3% /media/mmcboot /dev/zram0 49M 3.0M 43M 7% /var/log tmpfs 388M 0 388M 0% /run/user/0

    Korrekt die Größe angepasst!

    Schnell mal den USB3 testen

    root@rockpro64:~# sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync 4096+0 records in 4096+0 records out 4294967296 bytes (4.3 GB, 4.0 GiB) copied, 38.0723 s, 113 MB/s

    Der Adapter

    root@rockpro64:~# lsusb -vvv Bus 004 Device 002: ID 2109:0715 VIA Labs, Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 9 idVendor 0x2109 VIA Labs, Inc. idProduct 0x0715 bcdDevice 1.31 iManufacturer 1 VLI Manufacture String iProduct 2 VLI Product String iSerial 3 000000123ADA bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 121 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 224mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk-Only iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 1 bNumEndpoints 4 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 98 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 0 Command pipe (0x01) Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 MaxStreams 32 Data-in pipe (0x03) Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 15 MaxStreams 32 Data-out pipe (0x04) Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0400 1x 1024 bytes bInterval 0 bMaxBurst 0 MaxStreams 32 Status pipe (0x02) Binary Object Store Descriptor: bLength 5 bDescriptorType 15 wTotalLength 70 bNumDeviceCaps 4 FIXME: alloc bigger buffer for device capability descriptors Device Status: 0x0000 (Bus Powered)

    Ein lästiger Fehler weniger. 😉

  • 0 Stimmen
    1 Beiträge
    1k Aufrufe
    Niemand hat geantwortet
  • Release Empfehlung für Einsteiger

    Verschoben Archiv
    2
    0 Stimmen
    2 Beiträge
    1k Aufrufe
    FrankMF

    Sieht so aus, als wenn wir ein neues Traumpaar haben. 🙂

    0.7.7

    und

    rock64@rockpro64:/mnt$ uname -a Linux rockpro64 4.18.0-rc3-1046-ayufan-ge76778b6aa4b #1 SMP PREEMPT Thu Jul 19 14:10:17 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
  • Image 0.6.57 - NVMe paar Notizen

    Verschoben Archiv
    1
    0 Stimmen
    1 Beiträge
    642 Aufrufe
    Niemand hat geantwortet
  • bionic-minimal-rockpro64

    Verschoben Linux
    4
    0 Stimmen
    4 Beiträge
    1k Aufrufe
    FrankMF
    Neue Version 0.7.3

    Soll gefixt sein.

    USB2/3 PCIe LED's LED's

    Weiße LED starten nach dem Booten dauerhaft OK

    PCIe

    Treiber soll drin sein, aber die 3,3V werden nicht zur Karte durchgeschaltet. Somit funktioniert PCIe nicht.
    Nicht OK

    USB2

    USB-Funkadapter wird erkannt

    Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 002: ID 1113:3163 Medion AG Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

    Funktastur getestet OK

    USB3

    Angeschlossene SSD wird erkannt OK

    Kurzer Speed-Test. Bitte dran denken, wir haben hier noch kein optimiertes Release, sondern einen ersten Gehversuch. Da sind noch ganz viele Dinge anzupassen, was sicherlich noch Wochen, wenn nicht Monate dauert! Also, die Messergebnisse mit der nötigen Vorsicht genießen. Und dran denken, wenn @tkaiser das Ding richtig untersucht, dann haben wir auch ordentliche Meßergebnisse! 😉

    Haupt-PC

    2,5Zoll am USB3-Port

    sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync [sudo] Passwort für frank: 4096+0 Datensätze ein 4096+0 Datensätze aus 4294967296 bytes (4,3 GB, 4,0 GiB) copied, 38,171 s, **113 MB/s** ROCKPro64

    Ich benutze eine SAN Disk 240GB SSD an einem Inateck USB 3.0 2,5 Zoll Adapter.

    Info zum USB-Adapter

    lsusb Bus 004 Device 002: ID 174c:55aa ASMedia Technology Inc. ASM1051E SATA 6Gb/s bridge, ASM1053E SATA 6Gb/s bridge, ASM1153 SATA 3Gb/s bridge

    2,5 Zoll SSD am USB2-Port

    sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync 4096+0 records in 4096+0 records out 4294967296 bytes (4.3 GB, 4.0 GiB) copied, 160.058 s, **26.8 MB/s**

    2,5 Zoll SSD am USB3 Port

    sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync 4096+0 records in 4096+0 records out 4294967296 bytes (4.3 GB, 4.0 GiB) copied, 36.2588 s, **118 MB/s**

    Der @tkaiser erreicht deutlich höhere Geschwindigkeiten. Bis zu 400 MB/s. Hier nachzulesen.

    Wenn ich so einen iozone Test mache wie der Thomas, dann erreiche ich ähnliche Werte

    sudo iozone -a -g 1000m -s 1000m -i 0 -i 1 -r 16384K Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sat May 26 05:16:40 2018 Auto Mode Using maximum file size of 1024000 kilobytes. File size set to 1024000 kB Record Size 16384 kB Command line used: iozone -a -g 1000m -s 1000m -i 0 -i 1 -r 16384K Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 1024000 16384 383912 348782 1515506 1659394

    Da muss ich den Thomas nochmal was zu fragen. ?? 🤔

    UART2

    Und zum Schluss ist mir noch aufgefallen, das die UART2 Schnittstelle jetzt funktioniert 🙂 Ok, den Adapter, der morgen kommt, habe ich dann umsonst bestellt. LOL

    OK