Skip to content

[HOWTO] ROCKPro64 - PCIe NVMe Karte mit Samsung 960 EVO m.2

Verschoben Hardware
  • Das Bild sollte Euch ja mittlerweile bekannt vorkommen. 😉 Hier mal ein paar Dinge erklärt - Zielgruppe Einsteiger!

    0_1528781181138_IMG_20180523_111136.jpg

    Als erstes mal ein wichtiger Hinweis, von dieser Karte kann man aktuell nicht booten. Der U-Boot (Boatloader) unterstützt das zur Zeit nicht.

    Ich nutze für die Versuche hier, die erste Version die den PCIe-Port zum Leben erweckt.
    bionic-minimal-rockpro64-0.6.52-257-arm64.img.xz

     rock64@rockpro64:~$ uname -a
     Linux rockpro64 4.4.126-rockchip-ayufan-257 #1 SMP Sun Jun 10 18:30:43 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    Ein lspci zeigt uns ein paar Info's.

    rock64@rockpro64:~$ lspci
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100
    01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961
    

    Hier sehen wir die Rockchip Bridge, das ist der PCIe-Slot und die Samsung SSD. Das gibt es auch in ausführlicher.

    rock64@rockpro64:~$ sudo lspci -vvv
    [sudo] password for rock64: 
    00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 238
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
    	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
    		Address: 00000000fee30040  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 5GT/s, Width x2, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    	Kernel driver in use: pcieport
    
    01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 (prog-if 02 [NVM Express])
    	Subsystem: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 237
    	Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=16K]
    	Capabilities: [40] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+
    		Address: 0000000000000000  Data: 0000
    	Capabilities: [70] Express (v2) Endpoint, MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
    		LnkCap:	Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L0s unlimited, L1 <64us
    			ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
    		LnkCtl:	ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 5GT/s, Width x2, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [b0] MSI-X: Enable+ Count=8 Masked-
    		Vector table: BAR=0 offset=00003000
    		PBA: BAR=0 offset=00002000
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [148 v1] Device Serial Number 00-00-00-00-00-00-00-00
    	Capabilities: [158 v1] Power Budgeting <?>
    	Capabilities: [168 v1] #19
    	Capabilities: [188 v1] Latency Tolerance Reporting
    		Max snoop latency: 0ns
    		Max no snoop latency: 0ns
    	Capabilities: [190 v1] L1 PM Substates
    		L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
    			  PortCommonModeRestoreTime=10us PortTPowerOnTime=10us
    		L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
    			   T_CommonMode=0us LTR1.2_Threshold=0ns
    		L1SubCtl2: T_PwrOn=10us
    	Kernel driver in use: nvme
    

    Viele Dinge, wo man keine Ahnung von hat, auch ich nicht 😉 Aber, es gibt auch hier interessante Info's.

    LnkSta:	Speed 5GT/s, Width x2, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    

    Was sagt uns diese Zeile? Die SSD ist mit zwei Lanes (x2) an den Prozessor angebunden. Oder sollte? Der Adapter soll eigentlich x4 unterstützen.

    Laut diesem Link hier, sollte sie maximal 800 MB/s schaufeln.

    Etwas vom Thema abgekommen. Also zurück. Wir wissen jetzt das die SSD vorhanden ist. Ein sudo fdisk -l gibt folgendes aus.

    rock64@rockpro64:~$ sudo fdisk -l
    Disk /dev/ram0: 4 MiB, 4194304 bytes, 8192 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    
    
    Disk /dev/mmcblk0: 14.7 GiB, 15811477504 bytes, 30881792 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disklabel type: gpt
    Disk identifier: 298096AF-4287-4988-B53A-24CDE27C1C8D
    
    Device          Start      End  Sectors  Size Type
    /dev/mmcblk0p1     64     8063     8000  3.9M Linux filesystem
    /dev/mmcblk0p2   8064     8191      128   64K Linux filesystem
    /dev/mmcblk0p3   8192    16383     8192    4M Linux filesystem
    /dev/mmcblk0p4  16384    24575     8192    4M Linux filesystem
    /dev/mmcblk0p5  24576    32767     8192    4M Linux filesystem
    /dev/mmcblk0p6  32768   262143   229376  112M Microsoft basic data
    /dev/mmcblk0p7 262144 30881758 30619615 14.6G Linux filesystem
    
    
    Disk /dev/nvme0n1: 232.9 GiB, 250059350016 bytes, 488397168 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    
    
    Disk /dev/zram0: 323 MiB, 338722816 bytes, 82696 sectors
    Units: sectors of 1 * 4096 = 4096 bytes
    Sector size (logical/physical): 4096 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    
    
    Disk /dev/zram1: 323 MiB, 338722816 bytes, 82696 sectors
    Units: sectors of 1 * 4096 = 4096 bytes
    Sector size (logical/physical): 4096 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    
    
    Disk /dev/zram2: 323 MiB, 338722816 bytes, 82696 sectors
    Units: sectors of 1 * 4096 = 4096 bytes
    Sector size (logical/physical): 4096 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    
    
    Disk /dev/zram3: 323 MiB, 338722816 bytes, 82696 sectors
    Units: sectors of 1 * 4096 = 4096 bytes
    Sector size (logical/physical): 4096 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    
    
    Disk /dev/zram4: 323 MiB, 338722816 bytes, 82696 sectors
    Units: sectors of 1 * 4096 = 4096 bytes
    Sector size (logical/physical): 4096 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    
    
    Disk /dev/zram5: 323 MiB, 338722816 bytes, 82696 sectors
    Units: sectors of 1 * 4096 = 4096 bytes
    Sector size (logical/physical): 4096 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    

    Der interessante Teil.

    Disk /dev/nvme0n1: 232.9 GiB, 250059350016 bytes, 488397168 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    

    ACHTUNG! Ab hier besteht die Gefahr von Datenverlust. Bitte vorher das Gehirn einschalten und denkt dran, ich übernehme kein Garantie für Eure Daten 🙂

    Eine jungfräuliche Karte muss jetzt erst mal eingerichtet werden. Mit sudo fdisk /dev/nvme0n1

    fdisk /dev/nvme0n1
    Welcome to fdisk (util-linux 2.25.2).
    Changes will remain in memory only, until you decide to write them.
    Be careful before using the write command.
    
    Command (m for help): n
    Partition type
    p primary (0 primary, 0 extended, 4 free)
    e extended (container for logical partitions)
    Select (default p): p
    Partition number (1-4, default 1): 1
    First sector (2048-488397168, default 2048): 2048
    Last sector, +sectors or +size{K,M,G,T,P} (2048-488397168, default 488397168): 488397168
    Created a new partition 1 of type 'Linux' and of size 232,9 GiB.
    
    Command (m for help): w
    The partition table has been altered.
    Calling ioctl() to re-read partition table.
    Syncing disks.
    

    Danach noch formatieren.

    mkfs.ext4 /dev/nvme0n1
    

    Mit

    mount /dev/nvme0n1 /mnt/
    

    wird die SSD dann ins System eingehangen.

    Speedtest

    Schreibtest

    rock64@rockpro64:/mnt$ sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync
    4096+0 records in
    4096+0 records out
    4294967296 bytes (4.3 GB, 4.0 GiB) copied, 12.6595 s, 339 MB/s
    rock64@rockpro64:/mnt$ sudo dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync
    4096+0 records in
    4096+0 records out
    4294967296 bytes (4.3 GB, 4.0 GiB) copied, 12.6277 s, 340 MB/s
    

    Lesetest

    rock64@rockpro64:/mnt$ sudo hdparm -tT /dev/nvme0n1
    
    /dev/nvme0n1:
     Timing cached reads:   2562 MB in  2.00 seconds = 1280.89 MB/sec
     Timing buffered disk reads: 1734 MB in  3.00 seconds = 577.90 MB/sec
    

    Das Ganze mal laut dieser Anleitung.

    rock64@rockpro64:/mnt$ sudo dd if=/dev/zero of=tempfile bs=1M count=1024 conv=fdatasync,notrunc 
    1024+0 records in
    1024+0 records out
    1073741824 bytes (1.1 GB, 1.0 GiB) copied, 3.41565 s, 314 MB/s
    rock64@rockpro64:/mnt$ echo 3 | sudo tee /proc/sys/vm/drop_caches 
    3
    rock64@rockpro64:/mnt$ dd if=tempfile of=/dev/null bs=1M count=1024 
    1024+0 records in
    1024+0 records out
    1073741824 bytes (1.1 GB, 1.0 GiB) copied, 1.62841 s, 659 MB/s
    rock64@rockpro64:/mnt$ dd if=tempfile of=/dev/null bs=1M count=1024 
    1024+0 records in
    1024+0 records out
    1073741824 bytes (1.1 GB, 1.0 GiB) copied, 0.701997 s, 1.5 GB/s
    rock64@rockpro64:/mnt$ dd if=tempfile of=/dev/null bs=1M count=1024 
    1024+0 records in
    1024+0 records out
    1073741824 bytes (1.1 GB, 1.0 GiB) copied, 0.664641 s, 1.6 GB/s
    rock64@rockpro64:/mnt$ dd if=tempfile of=/dev/null bs=1M count=1024 
    1024+0 records in
    1024+0 records out
    1073741824 bytes (1.1 GB, 1.0 GiB) copied, 0.681466 s, 1.6 GB/s
    rock64@rockpro64:/mnt$ dd if=tempfile of=/dev/null bs=1M count=1024 
    1024+0 records in
    1024+0 records out
    1073741824 bytes (1.1 GB, 1.0 GiB) copied, 0.687785 s, 1.6 GB/s
    

    Nun müsste man die Testergebnisse einschätzen können. Da das meine erste SSD in einem PCIe Steckplatz ist, kann ich das nicht so richtig. Fakt ist, eigentlich müsste da was mehr gehen. Ich überlasse mal die Einschätzung anderen. @tkaiser

    Fazit:

    Das könnte ein richtig interessantes SOC werden, ich träume jetzt mal was. Booten von der PCIe-SSD und an USB3 ein Datengrab. Könnte ein sehr vielversprechendes NAS werden oder was auch immer. Viel Spaß beim Testen!!

    Und Danke an Kamil für seine Arbeit an diesem Linux-Image!

  • Ergänzung

    Eine andere SATA-Karte und eine Riser-Karte mit angeschlossener GPU startet nicht.

    rock64@rockpro64v2_1:~$ uname -a
    Linux rockpro64v2_1 4.4.132-1075-rockchip-ayufan-ga83beded8524 #1 SMP Thu Jul 26 08:22:22 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

  • ROCKPro64 - Samsung Portable SSD T5 500GB

    Hardware
    1
    0 Stimmen
    1 Beiträge
    278 Aufrufe
    Niemand hat geantwortet
  • 0 Stimmen
    1 Beiträge
    292 Aufrufe
    Niemand hat geantwortet
  • SATA Adapter - SSD kopieren

    Hardware
    1
    0 Stimmen
    1 Beiträge
    179 Aufrufe
    Niemand hat geantwortet
  • SATA Karte Marvell 88SE9230 Chipsatz mit 0.9.16

    Hardware
    8
    0 Stimmen
    8 Beiträge
    599 Aufrufe
    FrankMF

    Gestern hat Kamil einen neuen Kernel released, so das ich das heute mal auf dem NAS probiert habe. Durch den Boot von der USB-SSD sollten die Pfade ja alle passen und man problemlos den Kernel updaten können.

    root@rockpro64:/usr/local/sbin# df -h Dateisystem Größe Benutzt Verf. Verw% Eingehängt auf udev 992M 0 992M 0% /dev tmpfs 199M 5,5M 194M 3% /run /dev/sdc7 459G 3,3G 437G 1% / tmpfs 995M 0 995M 0% /dev/shm tmpfs 5,0M 4,0K 5,0M 1% /run/lock tmpfs 995M 0 995M 0% /sys/fs/cgroup /dev/sdc6 112M 4,0K 112M 1% /boot/efi /dev/md0 3,6T 485G 3,0T 14% /mnt/nas tmpfs 199M 0 199M 0% /run/user/1000

    Gut, /boot liegt auf der USB-SSD. Also, wie bekannt, den Kernel heruntergeladen und installiert. Nach dem Neustart geht nix 😞 Mittels HDMI Monitor angeschlossen um den Fehler sehen zu können, da macht es auch schon Klick. Der Parameter

    pci=nomsi

    ist durch das Kernel-Update überschrieben worden. Ich hatte dann die USB-SSD ausgebaut und das Problem am lokalen Rechner gelöst. Aber, man ist ja faul.....;)

    Da es überschrieben wird, müssen auch irgendwo die Informationen dazu liegen.......

    /usr/local/sbin/update-extlinux.sh

    Da ist das File, was Kamil dafür angelegt hat.

    #!/bin/bash TIMEOUT="" DEFAULT="" APPEND="rw" APPEND="$APPEND panic=10" APPEND="$APPEND init=/sbin/init" APPEND="$APPEND coherent_pool=1M" APPEND="$APPEND ethaddr=\${ethaddr} eth1addr=\${eth1addr} serial=\${serial#}" APPEND="$APPEND cgroup_enable=cpuset cgroup_memory=1 cgroup_enable=memory swapaccount=1 pci=nomsi" [..........gekürzt.........]

    Hier seht ihr das File schon mit meiner Änderung, in der Hoffnung das es dann beim nächsten Mal ohne Probleme funktioniert. Bleibt nur noch das Problem, wann ändert Kamil das File, weil dann ist die Änderung wieder weg!?!?

  • [HOWTO] SD-Karte beschreiben

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    442 Aufrufe
    Niemand hat geantwortet
  • 0 Stimmen
    1 Beiträge
    637 Aufrufe
    Niemand hat geantwortet
  • OMV Images

    ROCKPro64
    3
    0 Stimmen
    3 Beiträge
    830 Aufrufe
    FrankMF

    Kurzes Update

    https://github.com/ayufan-rock64/linux-build/releases/download/0.8.0rc10/stretch-openmediavault-rockpro64-0.8.0rc10-1125-armhf.img.xz

    Startet 🙂 Incl. WiFi & PCIe NVMe SSD

    War aber nur ein ganz kurzer Test!!

  • ROCKPro64 - PCIe x4

    Verschoben Hardware
    13
    0 Stimmen
    13 Beiträge
    5k Aufrufe
    FrankMF

    @Northstar Hallo, laut meinen Info's nicht, hat irgendwas mit der Speicheradressierung zu tuen. Und Grafikkarten benötigen wohl zu viel. Das ist das, was ich bei den vielen Diskussionen im IRC so aufgeschnappt habe.

    Ich habe es auch schon mal genauso probiert - natürlich ohne Erfolg.