eth1
Die zweite LAN-Schnittstelle macht nur 100Mbit/s
oot@rockpi-e:~# iperf3 -c 10.10.1.3
Connecting to host 10.10.1.3, port 5201
[ 5] local 10.10.1.2 port 59576 connected to 10.10.1.3 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 13.0 MBytes 109 Mbits/sec 0 344 KBytes
[ 5] 1.00-2.00 sec 10.9 MBytes 91.7 Mbits/sec 0 344 KBytes
[ 5] 2.00-3.00 sec 11.1 MBytes 93.3 Mbits/sec 0 344 KBytes
[ 5] 3.00-4.00 sec 11.7 MBytes 98.5 Mbits/sec 0 344 KBytes
[ 5] 4.00-5.00 sec 11.1 MBytes 93.3 Mbits/sec 0 344 KBytes
[ 5] 5.00-6.00 sec 11.0 MBytes 92.3 Mbits/sec 0 344 KBytes
[ 5] 6.00-7.00 sec 11.1 MBytes 93.3 Mbits/sec 0 344 KBytes
[ 5] 7.00-8.00 sec 11.1 MBytes 92.8 Mbits/sec 0 344 KBytes
[ 5] 8.00-9.00 sec 11.8 MBytes 99.0 Mbits/sec 0 344 KBytes
[ 5] 9.00-10.00 sec 11.1 MBytes 93.3 Mbits/sec 0 344 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 114 MBytes 95.7 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 112 MBytes 94.1 Mbits/sec receiver
iperf Done.
root@rockpi-e:~# iperf3 -R -c 10.10.1.3
Connecting to host 10.10.1.3, port 5201
Reverse mode, remote host 10.10.1.3 is sending
[ 5] local 10.10.1.2 port 59580 connected to 10.10.1.3 port 5201
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 11.2 MBytes 94.2 Mbits/sec
[ 5] 1.00-2.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 2.00-3.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 3.00-4.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 4.00-5.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 5.00-6.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 6.00-7.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 7.00-8.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 8.00-9.00 sec 11.2 MBytes 93.9 Mbits/sec
[ 5] 9.00-10.00 sec 11.2 MBytes 93.9 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 113 MBytes 94.6 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 112 MBytes 94.0 Mbits/sec receiver
iperf Done.
Hier alles in Betrieb 😉
root@rockpi-e:~# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 62:ac:5f:a1:72:e9 brd ff:ff:ff:ff:ff:ff
inet 192.168.3.14/24 brd 192.168.3.255 scope global dynamic noprefixroute eth0
valid_lft 6829sec preferred_lft 6829sec
inet6 2a02:908:1265:fbf0:xxxx/64 scope global dynamic noprefixroute
valid_lft 7173sec preferred_lft 573sec
inet6 fe80::20b1:e533:69d5:f1e8/64 scope link noprefixroute
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 62:ac:5f:a1:72:09 brd ff:ff:ff:ff:ff:ff
inet 10.10.1.2/24 scope global eth1
valid_lft forever preferred_lft forever
4: wlx38014640991e: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 38:01:46:40:99:1e brd ff:ff:ff:ff:ff:ff
inet 192.168.178.26/24 brd 192.168.178.255 scope global dynamic noprefixroute wlx38014640991e
valid_lft 863627sec preferred_lft 863627sec
inet6 2a02:908:1265:fbe0:xxx/64 scope global dynamic noprefixroute
valid_lft 6829sec preferred_lft 3229sec
inet6 fe80::ac16:7a52:ac7b:13d3/64 scope link noprefixroute
valid_lft forever preferred_lft forever
Und dann noch
USB3
Mal schnell eine SSD angeklemmt, nix besonderes.
oot@rockpi-e:~# lsusb
Bus 005 Device 002: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. JMS567 SATA 6Gb/s bridge
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 0bda:d723 Realtek Semiconductor Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
dd
root@rockpi-e:/tmp/home/rock64# dd if=/dev/zero of=sd.img bs=1M count=4096 conv=fdatasync
4096+0 Datensätze ein
4096+0 Datensätze aus
4294967296 bytes (4,3 GB, 4,0 GiB) copied, 45,8441 s, 93,7 MB/s
So weit sollte alles funktionieren. Mal schauen was ich damit mache...
