Skip to content

ROCKPro64 (2GB) - Probleme mit der PCIe SATA-Karte??

ROCKPro64
  • Bedingt durch eine Diskussion gestern im IRC-Channel, habe ich heute beschlossen das Ganze mal was intensiver zu testen. Ist ja auch schon eine ganze Zeit lang her, das ich mein NAS zusammen gebaut habe.

    Blöd, das ich nur eine SATA-Karte habe, so muss ich mein NAS heute mal zerlegen....Ok, da ist die Karte.

    SATA_4.jpg

    Es müsste sich dabei um diese Karte hier handeln. Meine ist von pine64.org

    Was mir gerade noch einfällt, bei den ganzen Problemfällen, die es so gibt, wie versorgen die denn die HDD mit Spannung??

    Hier meine Variante

    IMG_20181225_084508_ergebnis.jpg

    IMG_20181225_084532_ergebnis.jpg

    Ok, dann mal ran ans testen

    ROCKPro64 v2.1. 2GB RAM Armbian

    Hardware

    • ROCKPro64 v2.1 2GB RAM
    • PCIe SATA-Karte
    • 1TB 2,5 Zoll HDD
    • Boot erfolgt von einer SD-Karte

    lspci -vvv schmeißt folgendes aus

    root@rockpro64:~# lspci -vvv
    00:00.0 PCI bridge: Device 1d87:0100 (prog-if 00 [Normal decode])
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 224
    	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    	I/O behind bridge: 00000000-00000fff
    	Memory behind bridge: fa000000-fa0fffff
    	Prefetchable memory behind bridge: 00000000-000fffff
    	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
    	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
    	Capabilities: [80] Power Management version 3
    		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
    		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
    	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
    		Address: 00000000fee30040  Data: 0000
    		Masking: 00000000  Pending: 00000000
    	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
    		Vector table: BAR=0 offset=00000000
    		PBA: BAR=0 offset=00000008
    	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
    		DevCap:	MaxPayload 256 bytes, PhantFunc 0
    			ExtTag- RBE+
    		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
    			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
    		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
    		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
    			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
    		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
    			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
    		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
    			Changed: MRL- PresDet- LinkState-
    		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
    		RootCap: CRSVisible-
    		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
    		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v2] Advanced Error Reporting
    		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
    		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
    		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
    		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
    		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
    	Capabilities: [274 v1] Transaction Processing Hints
    		Interrupt vector mode supported
    		Device specific mode supported
    		Steering table in TPH capability structure
    	Kernel driver in use: pcieport
    
    01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
    	Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
    	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    	Latency: 0
    	Interrupt: pin A routed to IRQ 225
    	Region 0: I/O ports at <unassigned> [disabled]
    	Region 1: I/O ports at <unassigned> [disabled]
    	Region 2: I/O ports at <unassigned> [disabled]
    	Region 3: I/O ports at <unassigned> [disabled]
    	Region 4: I/O ports at <unassigned> [disabled]
    	Region 5: Memory at fa010000 (32-bit, non-prefetchable) [size=512]
    	[virtual] Expansion ROM at fa000000 [disabled] [size=64K]
    	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
    		Address: fee30040  Data: 0000
    	Capabilities: [78] Power Management version 3
    		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
    		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
    	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
    		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
    			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
    		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
    			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
    			MaxPayload 128 bytes, MaxReadReq 512 bytes
    		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
    		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us
    			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
    		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
    			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
    		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
    		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
    		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
    		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
    			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
    			 Compliance De-emphasis: -6dB
    		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
    			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    	Capabilities: [100 v1] Virtual Channel
    		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
    		Arb:	Fixed- WRR32- WRR64- WRR128-
    		Ctrl:	ArbSelect=Fixed
    		Status:	InProgress-
    		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
    			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
    			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
    			Status:	NegoPending- InProgress-
    	Kernel driver in use: ahci
    

    Software

    Welcome to ARMBIAN 5.67.181217 nightly Debian GNU/Linux 9 (stretch) 4.4.167-rockchip64
    

    und mit

    Welcome to ARMBIAN 5.67 stable Debian GNU/Linux 9 (stretch) 4.4.166-rockchip64
    

    getestet!

    Wie ihr oben schon sehen könnt, wird die Hardware einwandfrei eingebunden, die HDD ist sofort erkennbar. Mit fdisk -l (gekürzt)

    Disk /dev/sda: 931.5 GiB, 1000204886016 bytes, 1953525168 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 4096 bytes
    I/O size (minimum/optimal): 4096 bytes / 4096 bytes
    Disklabel type: dos
    Disk identifier: 0x8786fc87
    
    Device     Boot Start        End    Sectors   Size Id Type
    /dev/sda1        2048 1953525167 1953523120 931.5G 83 Linux
    

    Ich hatte keine Probleme, die Karte zu mounten und mit ihr zu arbeiten. Auf beiden Versionen von Armbian (nightly und die normale) keine Probleme.

    ROCKPro64 v2.1. 2GB RAM Ayufan

    Hardware

    • ROCKPro64 v2.1 2GB RAM
    • PCIe SATA-Karte
    • 1TB 2,5 Zoll HDD
    • Boot erfolgt von einer SD-Karte

    lspci -vvv schmeißt folgendes aus

    rock64@rockpro64:~$ sudo lspci -vvv
     [sudo] password for rock64: 
     00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode])
     	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
     	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx-
     	Latency: 0
     	Interrupt: pin A routed to IRQ 238
     	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
     	I/O behind bridge: 00000000-00000fff
     	Memory behind bridge: fa000000-fa0fffff
     	Prefetchable memory behind bridge: 00000000-000fffff
     	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
     	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
     		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
     	Capabilities: [80] Power Management version 3
     		Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
     		Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+
     	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+
     		Address: 00000000fee30040  Data: 0000
     		Masking: 00000000  Pending: 00000000
     	Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
     		Vector table: BAR=0 offset=00000000
     		PBA: BAR=0 offset=00000008
     	Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00
     		DevCap:	MaxPayload 256 bytes, PhantFunc 0
     			ExtTag- RBE+
     		DevCtl:	Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
     			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
     			MaxPayload 128 bytes, MaxReadReq 512 bytes
     		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
     		LnkCap:	Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us
     			ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+
     		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
     			ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+
     		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
     		SltCap:	AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
     			Slot #0, PowerLimit 0.000W; Interlock- NoCompl-
     		SltCtl:	Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
     			Control: AttnInd Off, PwrInd Off, Power+ Interlock-
     		SltSta:	Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock-
     			Changed: MRL- PresDet- LinkState-
     		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible-
     		RootCap: CRSVisible-
     		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
     		DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+
     		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
     		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
     			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
     			 Compliance De-emphasis: -6dB
     		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
     			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
     	Capabilities: [100 v2] Advanced Error Reporting
     		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
     		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
     		UESvrt:	DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
     		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
     		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
     		AERCap:	First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
     	Capabilities: [274 v1] Transaction Processing Hints
     		Interrupt vector mode supported
     		Device specific mode supported
     		Steering table in TPH capability structure
     	Kernel driver in use: pcieport
     
     01:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 02) (prog-if 01 [AHCI 1.0])
     	Subsystem: ASMedia Technology Inc. ASM1062 Serial ATA Controller
     	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
     	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
     	Latency: 0
     	Interrupt: pin A routed to IRQ 239
     	Region 0: I/O ports at <unassigned> [disabled]
     	Region 1: I/O ports at <unassigned> [disabled]
     	Region 2: I/O ports at <unassigned> [disabled]
     	Region 3: I/O ports at <unassigned> [disabled]
     	Region 4: I/O ports at <unassigned> [disabled]
     	Region 5: Memory at fa010000 (32-bit, non-prefetchable) [size=512]
     	[virtual] Expansion ROM at fa000000 [disabled] [size=64K]
     	Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
     		Address: fee30040  Data: 0000
     	Capabilities: [78] Power Management version 3
     		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
     		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
     	Capabilities: [80] Express (v2) Legacy Endpoint, MSI 00
     		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
     			ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
     		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
     			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
     			MaxPayload 128 bytes, MaxReadReq 512 bytes
     		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
     		LnkCap:	Port #1, Speed 5GT/s, Width x1, ASPM not supported, Exit Latency L0s unlimited, L1 <2us
     			ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
     		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- CommClk-
     			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
     		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
     		DevCap2: Completion Timeout: Range ABC, TimeoutDis+, LTR-, OBFF Not Supported
     		DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
     		LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
     			 Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
     			 Compliance De-emphasis: -6dB
     		LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
     			 EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
     	Capabilities: [100 v1] Virtual Channel
     		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
     		Arb:	Fixed- WRR32- WRR64- WRR128-
     		Ctrl:	ArbSelect=Fixed
     		Status:	InProgress-
     		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
     			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
     			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
     			Status:	NegoPending- InProgress-
     	Kernel driver in use: ahci
    

    Software

    rock64@rockpro64:~$ uname -a
    Linux rockpro64 4.4.154-1124-rockchip-ayufan-ged3ce4d15ec1 #1 SMP Mon Oct 22 20:59:41 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    Danach die Platte mit fdisk -l angezeigt

    Disk /dev/sda: 223.6 GiB, 240057409536 bytes, 468862128 sectors
    Units: sectors of 1 * 512 = 512 bytes
    Sector size (logical/physical): 512 bytes / 512 bytes
    I/O size (minimum/optimal): 512 bytes / 512 bytes
    Disklabel type: dos
    Disk identifier: 0xaa1a7c28
    
    Device     Boot Start       End   Sectors   Size Id Type
    /dev/sda1       32768 468860927 468828160 223.6G 83 Linux
    

    Fazit

    Mit beiden aktuellen Linuxversionen, Armbian und Ayufan, geht die PCIe SATA-Karte problemlos. Bitte beachten, ich setze nur Serverversionen ein, die Desktop-Versionen sind aktuell noch viel zu fehleranfällig. Ob man die überhaupt nutzen kann, zur Zeit, möge jeder selber beurteilen.

    Es war egal, ob eine HDD oder eine SSD angeschlossen war. Auch hier bitte beachten, ich setze nur 2,5 Zoll HDDs ein. Aber, mit einer stabilen Spannungsversorgung sollten auch 3,5 Zoll HDDs kein Problem sein.

    In meinem NAS betreibe ich das Ganze mit zwei 2,5 Zoll HDDs mit dem gelieferten Stromadapter von pine64.org. Ich gehe davon aus, das das mit 3,5 Zoll HDDs so nicht geht, da diese einen höheren Strombedarf haben.

    Meine aktuelle Vermutung warum so viele Probleme haben, könnte an genau dieser Spannungsversorgung liegen. Ich werde jetzt den gleichen Test noch auf einem ROCKPro64 v2.0 mit 4GB RAM testen, weil die Vermutung im Raum liegt, das es da nicht geht. Da Ergebnis kommt dann in einem separaten Artikel.

    Viel Spaß beim NAS bauen!

    Auch mir hat das Testen geholfen, weil ich nun mein NAS umbauen kann auf Armbian und ich dann endlich eine zusätzliche HDD einbauen kann (USB3). Ich weiß ja, das die bei Armbian problemlos funktioniert. Ob das mit dem Strom dann noch passt, ok das werden wir dann sehen....

  • [V] ROCKPro64 incl. PCIe SATA-Karte

    Verschoben Archiv
    2
    0 Stimmen
    2 Beiträge
    207 Aufrufe
    FrankMF

    Verkauft!

  • 0 Stimmen
    1 Beiträge
    355 Aufrufe
    Niemand hat geantwortet
  • Kamil hat mal wieder Zeit?

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    448 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - USB3 Probleme

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    822 Aufrufe
    Niemand hat geantwortet
  • Booten von der NVMe Platte

    ROCKPro64
    16
    0 Stimmen
    16 Beiträge
    7k Aufrufe
    S

    Für dies Kernal: Linux rockpro64 4.4.167-1213-rockchip-ayufan-g34ae07687fce #1 SMP Tue Jun 18 20:44:49 UTC 2019 aarch64 GNU/Linux

    Booten von der NVMe Platte nicht möglich.

    Ich folgte die folgende Schritte. Leider funktioniert es nicht. Es gibt einen Fehler in Boot.

    Ohne RAID oder LVM config.

    Specs:
    Rockpro64
    Marvel PCIe 88se9230 karte
    SANDISK SSD 120 GB

  • Bionic-LXDE

    ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    492 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 wieder vorbestellbar

    ROCKPro64
    5
    0 Stimmen
    5 Beiträge
    977 Aufrufe
    FrankMF

    Meine Lieferung ist unterwegs 🙂

    Hello Mr. Frank Mankel, Order 62068 just shipped on July 18, 2018 from Shenzhen transit to Hong Kong DHL.

  • Benchmarks

    Angeheftet Verschoben Archiv
    10
    0 Stimmen
    10 Beiträge
    2k Aufrufe
    FrankMF
    iozone Test (0.6.52) Hardware

    Hardware ist eine Samsung EVO 960 m.2 mit 250GB

    Eingabe sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Ausgabe Run began: Thu Jun 14 12:04:01 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 40859 79542 101334 101666 31721 60459 102400 16 113215 202566 234307 233091 108334 154750 102400 512 362864 412548 359279 362810 340235 412626 102400 1024 400478 453205 381115 385746 372378 453548 102400 16384 583762 598047 595752 596251 590950 604690

    Zum direkten Vergleich hier heute mal mit 4.17.0-rc6-1019

    rock64@rockpro64:/mnt$ uname -a Linux rockpro64 4.17.0-rc6-1019-ayufan-gfafc3e1c913f #1 SMP PREEMPT Tue Jun 12 19:06:59 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux iozone Test rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sat Jun 16 06:34:43 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 48672 104754 115838 116803 47894 103606 102400 16 168084 276437 292660 295458 162550 273703 102400 512 566572 597648 580005 589209 534508 597007 102400 1024 585621 624443 590545 599177 569452 630098 102400 16384 504871 754710 765558 780592 777696 753426 iozone test complete.