Skip to content

ROCKPro64 v2.1 - Und wieder mal einer der Ersten? ;)

ROCKPro64
  • Vorderseite

    0_1532521590926_IMG_20180725_142018_ergebnis.jpg

    Rückseite

    0_1532521598304_IMG_20180725_141950_ergebnis.jpg

    Gerade den Karton geöffnet, kurzer Blick über's Board.

    • Der Widerstand für das PCIe Problem ist natürlich weg
    • gelbe Folie weg
    • WLan Bereich sieht überarbeitet aus, wie erwartet
    • vermisse den IR-Empfänger
    • sollte nicht unten rechts ein Taster rein?? (Habe ich aber noch nicht vermisst)
    • Recover Taster ist jetzt vorhanden! Auf dem oberen Bild oben links!

    Mehr und vor allen Dingen ausführlichere Info's folgen.

    Update

    Recovery Taster

    0_1532550859826_DSC_0032.JPG

  • Fangen wir vorne an. Das Paket ist angekommen 😉

    0_1532525467297_IMG_20180725_140809_ergebnis.jpg

    Was war drin?

    • ROCKPro64 2GB
    • Kühlkörper
    • 32GB eMMC Karte
    • USB3-to-SATA Adapter
    • Stromanschlüsse für SATA HDD's
    • WiFi Adapter

    Versand ist teuer 30$, dazu kommt dann noch Zoll und Handling ca. 41€. Aber, läuft alles perfekt und super schnell. Zweite Lieferung ohne Probleme!

    Wir kommen zum Board v2.1, das andere Board von mir war ein Vorserienmodell und hatte ja so seine Probleme. Die sollen aber jetzt gefixt sein. Das schauen wir uns dann mal an.

    ROCKPro64 v2.1 2GB RAM

    Problem Nr.1

    PCIe Schnittstelle bekam keine Spannung wegen einem überflüssigen Widerstand. https://forum.frank-mankel.org/topic/116/howto-smd-widerstand-preproduction-board

    Test

    Ich habe eine SSD und einen HDD angeschlossen, mittels zweier SATA Kabeln an der PCIe SATA Karte. Die Spannung für die 2,5 Zoll Festplatten kann man sich direkt vom Board holen. Vorne am Stromanschluß ist ein weißer Steckplatz, dieser stellt die Spannung zur Verfügung. Pine64 hat ein Kabel dafür im Angebot, welches ich mitbestellt habe.

    Nachdem ich alles zusammen gesteckt habe, startete der ROCKPro64 ohne Probleme.

    0_1532526926979_IMG_20180725_154746_ergebnis.jpg

    Eingesetztes Image

    rock64@rockpro64:/mnt$ uname -a
    Linux rockpro64 4.4.132-1072-rockchip-ayufan-ga1d27dba5a2e #1 SMP Sat Jul 21 20:18:03 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux
    

    Meine 2,5 Zoll SSD mit 240GB

    rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 
    	Iozone: Performance Test of File I/O
    	        Version $Revision: 3.429 $
    		Compiled for 64 bit mode.
    		Build: linux 
    
    	Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
    	             Al Slater, Scott Rhine, Mike Wisner, Ken Goss
    	             Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR,
    	             Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner,
    	             Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone,
    	             Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root,
    	             Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer,
    	             Vangel Bojaxhi, Ben England, Vikentsi Lapa.
    
    	Run began: Wed Jul 25 13:46:40 2018
    
    	Include fsync in write timing
    	O_DIRECT feature enabled
    	Auto Mode
    	File size set to 102400 kB
    	Record Size 4 kB
    	Record Size 16 kB
    	Record Size 512 kB
    	Record Size 1024 kB
    	Record Size 16384 kB
    	Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2
    	Output is in kBytes/sec
    	Time Resolution = 0.000001 seconds.
    	Processor cache size set to 1024 kBytes.
    	Processor cache line size set to 32 bytes.
    	File stride size set to 17 * record size.
                                                                  random    random     bkwd    record    stride                                    
                  kB  reclen    write  rewrite    read    reread    read     write     read   rewrite      read   fwrite frewrite    fread  freread
              102400       4     9411    15504    18778    18833    10727    12138                                                          
              102400      16    28420    52412    62043    62207    33101    37892                                                          
              102400     512   220877   253630   212220   213237   214789   245359                                                          
              102400    1024   172543   176752   165533   239463   237009   180548                                                          
              102400   16384   330306   211445   201754   331198   329653   218451                                                          
    
    iozone test complete.
    

    Meine 2,5 Zoll HDD, 1TB

    rock64@rockpro64:/media$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 
    	Iozone: Performance Test of File I/O
    	        Version $Revision: 3.429 $
    		Compiled for 64 bit mode.
    		Build: linux 
    
    	Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins
    	             Al Slater, Scott Rhine, Mike Wisner, Ken Goss
    	             Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR,
    	             Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner,
    	             Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone,
    	             Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root,
    	             Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer,
    	             Vangel Bojaxhi, Ben England, Vikentsi Lapa.
    
    	Run began: Wed Jul 25 13:52:56 2018
    
    	Include fsync in write timing
    	O_DIRECT feature enabled
    	Auto Mode
    	File size set to 102400 kB
    	Record Size 4 kB
    	Record Size 16 kB
    	Record Size 512 kB
    	Record Size 1024 kB
    	Record Size 16384 kB
    	Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2
    	Output is in kBytes/sec
    	Time Resolution = 0.000001 seconds.
    	Processor cache size set to 1024 kBytes.
    	Processor cache line size set to 32 bytes.
    	File stride size set to 17 * record size.
                                                                  random    random     bkwd    record    stride                                    
                  kB  reclen    write  rewrite    read    reread    read     write     read   rewrite      read   fwrite frewrite    fread  freread
              102400       4     8789    15033    18076    18175      552     1550                                                          
              102400      16    42530    51919    59579    61526     2178     8438                                                          
              102400     512   103850   103808   107850   111118    35341    57268                                                          
              102400    1024   102749   103920   106320   110932    56230    73157                                                          
              102400   16384    86098   104648   105439   108904   100171    99910                                                          
    
    iozone test complete.
    

    Kurzer Test von Platte zu Platte

    rock64@rockpro64:/mnt$ dd if=/mnt/sd.img of=/media/testfile bs=1G count=1 oflag=direct
    1+0 records in
    1+0 records out
    1073741824 bytes (1.1 GB, 1.0 GiB) copied, 13.0328 s, 82.4 MB/s
    

    Schaut soweit alles prima aus. Dem NAS bauen steht nichts mehr im Weg, oder!?

  • Ein paar Hardware Änderungen

    1. Weiße LED gedimmt

    0_1532529766212_IMG_20180725_151430_ergebnis.jpg

    1. Neue LED grün, neben dem Eingang der Stromversorgung

    0_1532529863801_IMG_20180725_151421_geändert.jpg

  • 0 Stimmen
    1 Beiträge
    471 Aufrufe
    Niemand hat geantwortet
  • 0 Stimmen
    1 Beiträge
    463 Aufrufe
    Niemand hat geantwortet
  • Der 3. ROCKPro64

    ROCKPro64
    3
    0 Stimmen
    3 Beiträge
    914 Aufrufe
    FrankMF

    Nachdem ich jetzt mein NAS neu gemacht habe, schauen wir mal, was die Chinesen geliefert haben. Bestellt hatte ich

    ROCKPro64 v2.1 2GB RAM Kühlkörper Netzteil 3A USB-Adapter für eMMC-Modul

    Endlich habe ich mal an den USB-Adapter für das eMMC-Modul gedacht 🙂

    0_1540029624802_IMG_20181020_115348_ergebnis.jpg

    Was ist mir aufgefallen? Das Versionsdatum ist neu (siehe oben) Die PCIe NVMe Karte ist neu

    Bei der PCIe NVMe Karte liegt eine Abstandshülse aus Messing und eine winzig kleine Schraube bei. Damit bekomme ich aber nicht die NVMe-SSD befestigt. Ich habe dann gemurkst 😉 Da sollte Pine64 unbedingt nachbessern!

    So sieht das dann zusammengebaut aus.

    0_1540029756582_IMG_20181020_115425_ergebnis.jpg

    0_1540029767082_IMG_20181020_115438_ergebnis.jpg

    Da ich ein paarmal gelesen hatte, das Leute Probleme mit dem PCIe NVMe Adapter hatten, direkt als erstes mal ein Test ob das reibungslos funktioniert.

    Sys rock64@rockpro64:/mnt$ uname -a Linux rockpro64 4.4.132-1075-rockchip-ayufan-ga83beded8524 #1 SMP Thu Jul 26 08:22:22 UTC 2018 aarch64 aarch64 aarch64 GNU/Linux lspci rock64@rockpro64:/mnt$ sudo lspci -vvv [sudo] password for rock64: 00:00.0 PCI bridge: Rockchip Inc. RK3399 PCI Express Root Port Device 0100 (prog-if 00 [Normal decode]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort+ <MAbort+ >SERR+ <PERR+ INTx- Latency: 0 Interrupt: pin A routed to IRQ 238 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00000000-00000fff Memory behind bridge: fa000000-fa0fffff Prefetchable memory behind bridge: 00000000-000fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [80] Power Management version 3 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0+,D1+,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME+ Capabilities: [90] MSI: Enable+ Count=1/1 Maskable+ 64bit+ Address: 00000000fee30040 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [b0] MSI-X: Enable- Count=1 Masked- Vector table: BAR=0 offset=00000000 PBA: BAR=0 offset=00000008 Capabilities: [c0] Express (v2) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0 ExtTag- RBE+ DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L1, Exit Latency L0s <256ns, L1 <8us ClockPM- Surprise- LLActRep- BwNot+ ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt+ AutBWInt+ LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd Off, Power+ Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL+ CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+ CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- DevCap2: Completion Timeout: Range B, TimeoutDis+, LTR+, OBFF Via message ARIFwd+ DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd- LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [274 v1] Transaction Processing Hints Interrupt vector mode supported Device specific mode supported Steering table in TPH capability structure Kernel driver in use: pcieport 01:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 (prog-if 02 [NVM Express]) Subsystem: Samsung Electronics Co Ltd NVMe SSD Controller SM961/PM961 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 237 Region 0: Memory at fa000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/32 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v2) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 8GT/s, Width x4, ASPM L1, Exit Latency L0s unlimited, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+ LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- CommClk- ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR+, OBFF Not Supported DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis- Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- Compliance De-emphasis: -6dB LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1- EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest- Capabilities: [b0] MSI-X: Enable+ Count=8 Masked- Vector table: BAR=0 offset=00003000 PBA: BAR=0 offset=00002000 Capabilities: [100 v2] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+ AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [148 v1] Device Serial Number 00-00-00-00-00-00-00-00 Capabilities: [158 v1] Power Budgeting <?> Capabilities: [168 v1] #19 Capabilities: [188 v1] Latency Tolerance Reporting Max snoop latency: 0ns Max no snoop latency: 0ns Capabilities: [190 v1] L1 PM Substates L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+ PortCommonModeRestoreTime=10us PortTPowerOnTime=10us L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1- T_CommonMode=0us LTR1.2_Threshold=0ns L1SubCtl2: T_PwrOn=10us Kernel driver in use: nvme

    Da sieht alles gut aus. x4 alles Bestens!

    iozone rock64@rockpro64:/mnt$ sudo iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Iozone: Performance Test of File I/O Version $Revision: 3.429 $ Compiled for 64 bit mode. Build: linux Contributors:William Norcott, Don Capps, Isom Crawford, Kirby Collins Al Slater, Scott Rhine, Mike Wisner, Ken Goss Steve Landherr, Brad Smith, Mark Kelly, Dr. Alain CYR, Randy Dunlap, Mark Montague, Dan Million, Gavin Brebner, Jean-Marc Zucconi, Jeff Blomberg, Benny Halevy, Dave Boone, Erik Habbinga, Kris Strecker, Walter Wong, Joshua Root, Fabrice Bacchella, Zhenghua Xue, Qin Li, Darren Sawyer, Vangel Bojaxhi, Ben England, Vikentsi Lapa. Run began: Sat Oct 20 10:08:28 2018 Include fsync in write timing O_DIRECT feature enabled Auto Mode File size set to 102400 kB Record Size 4 kB Record Size 16 kB Record Size 512 kB Record Size 1024 kB Record Size 16384 kB Command line used: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 Output is in kBytes/sec Time Resolution = 0.000001 seconds. Processor cache size set to 1024 kBytes. Processor cache line size set to 32 bytes. File stride size set to 17 * record size. random random bkwd record stride kB reclen write rewrite read reread read write read rewrite read fwrite frewrite fread freread 102400 4 63896 108269 91858 95309 32845 73173 102400 16 123393 236653 273766 275807 118450 199130 102400 512 471775 570571 484612 496942 441345 575817 102400 1024 544229 642558 508895 511834 486506 647765 102400 16384 1044520 1100322 1069825 1092146 1089301 1086757 iozone test complete.

    Das sieht nicht optimal aus, schau ich mir später an. Das hier soll nur ein kurzer Test sein ob das Board rennt 🙂

    Nachdem ich mittlerweile zwei ROCKPro64 im "produktiven" Einsatz habe, war es immer sehr mühsam mal eben was zu testen. Man will die anderen ja nicht immer ausmachen, dran rumhantieren usw. Deswegen jetzt der dritte, der im Moment dann die Rolle des Testkandidaten einnimmt. Ab sofort kann ich wieder nach Lust und Laune, neue Images testen usw.

  • 0 Stimmen
    1 Beiträge
    560 Aufrufe
    Niemand hat geantwortet
  • 0 Stimmen
    1 Beiträge
    1k Aufrufe
    Niemand hat geantwortet
  • ROCKPro WLan Modul

    Verschoben ROCKPro64
    1
    0 Stimmen
    1 Beiträge
    690 Aufrufe
    Niemand hat geantwortet
  • 0 Stimmen
    1 Beiträge
    572 Aufrufe
    Niemand hat geantwortet
  • ROCKPro64 - PCIe SATA Karte

    Verschoben Hardware
    13
    0 Stimmen
    13 Beiträge
    4k Aufrufe
    FrankMF

    @elRadix : With pine64 sata-card you can use two hdd's. https://www.pine64.org/?product=rockpro64-pci-e-to-dual-sata-ii-interface-card

    For working cards please look into this thread before you buy anything.