Skip to content

FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6

Linux
  • Hey,

    I will do it in english, hope it is okay. Thanks, for very informative forum.

    My question is, is it possible to control the FAN in the newest OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6?
    The install was very easy no problems at all, the only problem is i did try some different commands to reach the fan, but was not able to get it going. Do somebody know how? Thanks.

    Best Regards.
    Soeren

  • Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

  • @mabs sagte in FAN control OMV Auyfan 0.10.12: gitlab-ci-linux-build-184, Kernel 5.6:

    Hi Soeren,

    I have this succesfully running.

    Kind Regards
    Martin

    Thanks, i will try the fan tool again. I'm almost sure i did try without luck, have you edited something in the fan tool conf..?

  • Hi,

    I only played with two parameters.

    I have two rockpro64 boards, currently one has a small fan and the other one has a large fan.

    Therefore I changed PROFILE_NR accordingly.

    Also I have ALWAYS_ON on true on the one with the large fan, but don't see a difference. The fan goes on and off still, maybe I misinterpreted the parameter.

    Also I just noticed now that the CTL settings of the version on github changed slightly, but I think this only improved the detection depending of the kernel settings.

    M

  • @mabs

    With the new OMV kernel 5.6 image from Auyfan, i can't get the FAN to spin - If the fan spins it runs really slow, no sound from the fan.

    With the FAN tool the master installation "failed" and with the release installation it did report "active"..
    I have installed a 92mm FAN inside the NAS case, it runs on Armbian with kernel 5.4.32

    I will open op the case later today to be sure. Thanks.

  • Hi,

    Now i did find the fan, here it goes "nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1" it is at "0" can be controlled to "255"

    Best Regards.

  • Yes that is basically the way ATS is doing the changing as well I think, as those /sys entries are in the _CTL variables.

    good that you got it working, or are you only half way?

    M

  • @mabs

    The tool works on all image under 5.4 or so for me. But yes i am at the finish line, just wanted the fan to be always on. Just wanted to share, if someone will run in the same problems. Thanks.

  • Helpful Thread!

    But, ATS don't work for me on kernel 5.6 with ayufan release. Only this command works.

    nano /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    Thanks @soerenderfor for the hint.

  • Ok, problem in ATS is this?

    -- FAN Control[ String ]
    	PWM_CTL		= {
    			"/sys/class/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    			"/sys/devices/platform/pwm-fan/hwmon/hwmon1/pwm1"
    	},
    
  • @FrankM - did you try fix the ATS tool, if yes. Will it Work?

    Best Regards.

  • Hi,

    since I'm currently change my rockpro64 setup I came across this.

    With the kernel from ayufan you need to set PWM_CTL to

    /sys/devices/platform/pwm-fan/hwmon/hwmon3/pwm1
    

    for my self compiled one I need

    /sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1
    

    But I got it only working with one entry for PWM_CTL e.g.

    PWM_CTL		= "/sys/devices/platform/pwm-fan/hwmon/hwmon0/pwm1",
    

    after that you need to start ats again

    sudo systemctl stop ats
    sudo systemctl start ats
    

    initially the fan should start immediately for a short period of time.

    In case it is even a different one on your kernel you can find the right one using this command.

    sudo find /sys -name pwm1 | grep hwmon
    

    So far I'm not sure which kernel parameter or modul changes this.

    Martin

  • 0 Stimmen
    1 Beiträge
    153 Aufrufe
    Niemand hat geantwortet
  • Docker & Redis Datenbank

    Verschoben Linux
    2
    0 Stimmen
    2 Beiträge
    154 Aufrufe
    FrankMF

    @FrankM sagte in Docker & Redis Datenbank:

    save 60 1
    #save 900 1
    save 300 10
    save 60 10000

    Hier kann man auch noch schön sehen, wie ich gekämpft habe, bis ich mal eine dump.rdb gesehen habe. Auch irgendwie logisch, das ich nie eine gesehen hatte, wenn man weiß das

    save 900 1

    bedeutet, das er alle 900 Sekunden speichert, wenn mindestens eine Änderung vorhanden ist. Das kann dann schon was dauern. Ich habe das dann mal verkürzt, damit ich schneller ein Ergebnis habe.

    save 60 1

    Das brachte mich dann dem Ziel näher. Danach konnte ich die dump.rdb auch finden.

    Bitte keine Redis DB ohne Passwort laufen lassen!
  • 0 Stimmen
    3 Beiträge
    324 Aufrufe
    FrankMF

    @thrakath1980 Das kann ich Dir leider nicht beantworten. Denke aber, das es sinnvoll ist neu anzufangen. Welche Settings meinst Du?

    Ich würde mal /etc/config sichern. Da sollte das Meiste ja drin sein.

    Notifications? Hmm, ich hoffe das das funktioniert. Ich schau zur Sicherheit mal nach.

  • Mobian - vollverschlüsselt

    Software
    1
    0 Stimmen
    1 Beiträge
    237 Aufrufe
    Niemand hat geantwortet
  • 1 Stimmen
    1 Beiträge
    253 Aufrufe
    Niemand hat geantwortet
  • Kernel-Log 4.20

    Linux
    1
    0 Stimmen
    1 Beiträge
    300 Aufrufe
    Niemand hat geantwortet
  • Mainline Kernel 4.18.0-rc3

    Linux
    1
    0 Stimmen
    1 Beiträge
    946 Aufrufe
    Niemand hat geantwortet
  • Mainline Kernel 4.17-rc7

    Verschoben Archiv
    8
    0 Stimmen
    8 Beiträge
    2k Aufrufe
    FrankMF

    4.17.0-rc6-1029-ayufan released

    Link Preview Image Releases · ayufan-rock64/linux-mainline-kernel

    Linux kernel source tree. Contribute to ayufan-rock64/linux-mainline-kernel development by creating an account on GitHub.

    favicon

    GitHub (github.com)

    Seit 1021 funktioniert USB3.